Quick pic of Snoon's GTi-R

Forums » Photo Zone » Quick pic of Snoon's GTi-R

Bookmark: delicious digg reddit furl yahoo google faves stumbleupon Facebook

Posted on: 24 August 2009 03:17 PM
snoon
Basic Member
Male, Wakefield
United Kingdom

Make: Nissan
Model: Pulsar GTiR
Total Posts 65

" I'll get some more pics done of engine bay etc once it's had a clean up. Currently in the process of having my Haltech E8 ECU mapped. Spec is..... Haltech E8 ECU with 3 Bar MAP sensor Anti-Lag & Launch control 86.5mm Wossner Forged Pistons Lighted and polished crank HKS 1.2mm Head Gasket SARD Purple 550cc Injectors Gizzmo IBC T28 with 360 degree Thurst Bearings - Built by AET Forge FMIC with custom pipe run Walbro 255 fuel pump Helix Organic Clutch full 3"" exhaust including Elbow/downpipe by TRL Blitz Induction with custom pipe run Grooved and vented discs Battery relocated to boot Engine built by Andrew Speck (08 & 09 FWD winner TOTB - Fastest Tigra on the planet!) Probably a load of stuff I can't remember too. Was last dyno'd at TDI North when it was running my Dastec Unichip prior to the Haltech being fitted and was running 350.5BHP and 349 ft/Lbs torque at 1.4 Bar boost. Most expensive mod was the rebuild at around _Ǭ£2k. Best BHP for _Ǭ£_Ǭ£_Ǭ£'s spent mod was my elbow/downpipe. Gained 25BHP for _Ǭ£280. Plans are to get it running sweet on the E8 then have a clean up of the paint work. Then I can drive it like I stole it!!!!!"

Posted on: 24 August 2009 07:44 PM
JSweete
Full Club Member
Male, York
United Kingdom

Make: Nissan
Model: 200SX
Total Posts 2060

looking very nice mate love the colour. Some serious money put in too whats the anti lag launch control like? do you find you get much lagg on the T28?




Posted on: 25 August 2009 10:19 AM
snoon
Basic Member
Male, Wakefield
United Kingdom

Make: Nissan
Model: Pulsar GTiR
Total Posts 65

"Not had the launch or anti lag switched on yet - My head gasket went when mapping so didn't get round to it. I'll let you know once I'v been to the racing line. It's pretty good Lag wise - Hitting 1 bar around 2.5 - 3k and hitting full 1.6 bar by 3.5 - 4k and holding rigt through to 6.5 - 7k."

Posted on: 26 August 2009 11:01 AM
JSweete
Full Club Member
Male, York
United Kingdom

Make: Nissan
Model: 200SX
Total Posts 2060

sounds good is it the CA engine you have in this then? (sure i asked you this before but i forgot what you said)




Posted on: 26 August 2009 01:43 PM
AndyW
Basic Member
Male, Goole
United Kingdom

Make: Nissan
Model: Silvia S15 Spec R
Total Posts 26

impressive spec mate - very nice car!

Posted on: 27 August 2009 01:33 PM
snoon
Basic Member
Male, Wakefield
United Kingdom

Make: Nissan
Model: Pulsar GTiR
Total Posts 65

"It the SR20DET engine in the R. Great engine - if looked after. I'll stick a post up when I finally get round to having it mapped let you know what I think of the Haltech as not many people in the UK are using them yet. Big down under though."

Posted on: 03 February 2010 03:12 PM
snoon
Basic Member
Male, Wakefield
United Kingdom

Make: Nissan
Model: Pulsar GTiR
Total Posts 65

"Quick pic of the power graph after having the e8 mapped....... Just at 1.2 Bar. "

Posted on: 03 February 2010 04:40 PM
boosted_brit
Basic Member
(No avatar)
Male, leeds
United Kingdom

Make: Not Specified
Model: Not Specified
Total Posts 21

Pocket rocket nice car you got there matey.

Posted on: 26 February 2010 09:12 PM
focipaul
Basic Member
(No avatar)
Male, Blackpool
United Kingdom

Make: Ford
Model: Focus
Total Posts 1218

What gearbox you got as heard lots of thinks that they are like chocolate.

Posted on: 20 March 2015 03:46 PM
david220
Basic Member
(No avatar)
Male, Preston
United Kingdom

Make: Not Specified
Model: Not Specified
Total Posts 19

hi

your car looks great why dont you upload the picture to http://www.modifiedcarpictures.co.uk/

regards
dave